APG Toolbox
Practical charts, calculators and references for mechanics, builders and DIYers.
Build your knowledge with automotive, boating, towing, tools, small engines, welding, electrical and safety practice, plus New York CDL and motorcycle topics.
Open Practice Tests →One tool at a time. Choose the tool you need above.
Sign in to printCommon approximately 75% thread drill sizes. Select a chart or search all charts.
SAE Coarse (UNC)
| Thread | Tap drill | Decimal |
|---|---|---|
| #4-40 UNC | #43 | 0.0890 in |
| #6-32 UNC | #36 | 0.1065 in |
| #8-32 UNC | #29 | 0.1360 in |
| #10-24 UNC | #25 | 0.1495 in |
| 1/4-20 UNC | #7 | 0.2010 in |
| 5/16-18 UNC | F | 0.2570 in |
| 3/8-16 UNC | 5/16 | 0.3125 in |
| 7/16-14 UNC | U | 0.3680 in |
| 1/2-13 UNC | 27/64 | 0.4219 in |
| 9/16-12 UNC | 31/64 | 0.4844 in |
| 5/8-11 UNC | 17/32 | 0.5313 in |
| 3/4-10 UNC | 21/32 | 0.6563 in |
Cutting-tap recommendations vary with material and desired thread engagement. Forming taps and tapered pipe threads may require different preparation—verify the tap manufacturer’s recommendation.
One inch divided into sixteenths. Longer marks represent larger fractions.
Tip: count the smallest marks between whole-inch numbers. Most standard tapes use 1/16-inch divisions; some precision tapes also show 1/32-inch marks.
inches × 25.4 = millimeters
Fastener grade is not a torque specification. Lubrication, coatings, joint design and service requirements change torque.
Current tire
New tire
Estimate assumes no converter or clutch slip.
| Current | Short run* | Longer run* |
|---|---|---|
| 5 A | 18 AWG | 16 AWG |
| 10 A | 16 AWG | 14 AWG |
| 20 A | 12 AWG | 10 AWG |
| 30 A | 10 AWG | 8 AWG |
| 40 A | 8 AWG | 6 AWG |
*General copper-wire starting point. Length, bundling, temperature and allowable voltage drop matter. Fuse the circuit for the wire and device.
Add a vehicle for more useful context, or look up a code without one. VIN entry is optional.
Random or multiple-cylinder misfire detected.
Common symptoms
- Rough running or shaking
- Loss of power
- Flashing or steady check-engine light
Possible causes
- Worn spark plugs or ignition fault
- Vacuum leak
- Fuel-delivery problem
- Low compression
- Incorrect valve or ignition timing
Check first
- Do not continue driving with a flashing check-engine light
- Read related cylinder-specific and fuel-trim codes
- Inspect plugs, coils and ignition components
- Check for vacuum leaks and verify fuel pressure
- Perform compression testing when needed
Possible repairs
- Replace only confirmed faulty ignition parts
- Repair vacuum or fuel-delivery faults
- Correct mechanical compression or timing problems
Manufacturer-specific and enhanced codes can differ by year, make, model, engine and installed equipment. Always confirm the exact definition and procedure with reliable vehicle-specific service information.
Create a printable sale record for most vehicles and vessels. Everything stays on this device and clears when the page is refreshed.
Passenger vehicle Bill of Sale
New York
For the total consideration of ________________, paid by Cash, the seller transfers the property described below to the buyer on ________________.
The seller certifies that the information provided is true to the best of the seller’s knowledge and that the seller has the legal right to transfer this property. The buyer acknowledges receipt and acceptance of the property under the terms stated above.
Also verify payload, tongue weight, hitch, axle, tire and combined-weight ratings.
Use the engine maker’s recommended wide-open-throttle RPM range. Never select a propeller by this estimate alone.
- Confirm year, make, model and engine
- Identify transmission/drive unit
- Check owner or factory service manual
- Match required specification—not color alone
- Measure drained quantity when appropriate
- Fill, run, inspect and recheck at specified temperature
- Engine oil level and leaks
- Coolant level and visible leaks
- Brake fluid and pedal feel
- Tire pressure, tread and damage
- Exterior lights and signals
- Wipers and washer fluid
- Battery terminals and hold-down
- Belts and accessible hoses
- Steering and suspension concerns
- Unusual warning lights, noises or smells
- Emergency equipment and documentation
- Record mileage and next service due
| Marking | System | General identification |
|---|---|---|
| No radial lines | SAE | Grade 2 |
| 3 radial lines | SAE | Grade 5 |
| 6 radial lines | SAE | Grade 8 |
| 8.8 | Metric | Property class 8.8 |
| 10.9 | Metric | Property class 10.9 |
| 12.9 | Metric | Property class 12.9 |
